Other Products: Smooth white cardstock, Distress Ink, Peacock Feather, Sequins mix, Rajni Chawla's Twinkling Spark. Glossy Accent and Swarovski crystals, and Red Tacky Tape,

For more tips on creating with the Patchwork Daisy collection, watch the tutorial at https://youtu.be/v5BEpcSlmoI.

Instructions: Choose a 6" by 6" card panel from the designer paper collection. Cut apart the outer teal color border. Next, cut the window with the help of Cut Mat Create 2A die. Adhere Clear cardstock to the back of the window using red tacky tape.

Stamp the Images from Patchwork Daisy Border Cling Stamp Set and Patchwork Daisy Cling Stamp Set, using black archival ink. Color the images with Zig Clean Clear Brush Markers and cut them with their coordinating dies. Also, cut one extra die cut of both the images for mating behind the painted images.

Once the images are ready, Cut a 6" by 6" teal color paper from the paper collection, glue down the negative of the window in the center. Adhere double layer of double-sided foam tape, add sequins and close the window.

Cut the corners of the teal color mat with a corner rounder and glue 8 pieces of white fancy laces from Elegant Pocket Accents Die, as shown.

Layer the ready window panel on the ready top folding card base, measuring 6 1/2" by 6 1/2". To finish the card, arrange the elements as shown and add Twinkling Spark with the help of an adhesive that dries clear.

Other Products: White card stock; Ranger Archival Ink Pad, Aquamarine, Pale Ochre; gold thread; ribbon, blue, white; gold wired ribbon; Stickles, Diamond; glossy accents; Diamond Dust Glitter

For more tips on creating with the Patchwork Daisy collection, watch the tutorial at https://youtu.be/v5BEpcSlmoI.

For more tips on creating with the tags & sentiments, watch the tutorial at https://youtu.be/eAfLuNkRda4.

For more tips on creating with the pocket dies, watch the tutorial at https://youtu.be/uDhKUj9AAMo.

Instructions: For card base, cut a piece of white card stock 6" x 12", fold in half with top fold. Cut design paper 5 3/4" square. Place the small straight die from the Decorative Pocket Accents Die 1 3/4" up from the bottom edge and cut. Die cut the larger piece and glue over the straight cut. Using both frame pieces from the Hand-Stitched Accents Die, cut from white card stock. Cut a piece of design paper to fit behind the frame and adhere. From white card stock, cut the Elegant Pocket Accents Die and adhere to the left side of the frame. Slip the frame into the straight cut and adhere. Add foam tape to the back of the 5 3/4" square piece and add to the card base.

Stamp the 2 floral images from the Patchwork Daisy Border set on white card stock with Bamboo Leaves. Stamp 2 more with Aquamarine. Die cut with coordinating dies. Cut the blue flowers off and add to the green sprays. Stamp the Buttons and Blooms flowers with Aquamarine and Magenta Hue, sponge edges with same inks. Die cut with coordinating dies. Create 2 small pink flowers and 1 large blue. Stamp buttons with Pale Ochre, die cut with coordinating die. Add glossy accents. Add to pink and blue flowers. Add Nuvo drops to smaller flowers and sprinkle glitter over drops. Add Diamond stickles to flowers. Stamp Leafy Accents with Bamboo Leaves and cut with coordinating die. Cut off a small portion to use under large blue flower.

Stamp sentiment and die cut with round tag from the Ornamental Tags Die set. Sponge edge with Magenta Hue. Add ribbon to tag. Add to card with foam tape.

Other Products: Creative Expressions Watercolour cardstock, white ribbon

For more tips on creating with the Patchwork Daisy collection, watch the tutorial at https://youtu.be/v5BEpcSlmoI.

For more tips on creating with the border dies & foldout cards, watch the tutorial at https://youtu.be/wxX94X84kUo.

Instructions: For more detailed photos and instructions, please visit my blog here. Die cut the patterned paper for the layers of the fold out card. Die cut the eyelet edge die from the HCD1-Patchwork Daisy Border Die set out of white cardstock and adhere to each layer of the card. Adhere the patterned paper over the border dies on each fold of the card. Die cut the lace edge die from the HCS1-7120 Fleur Border Basics set out of white cardstock and colour with Magenta Hue and Garden Patina inks. Add Frosting Powder to the edges using Dries Clear glue with a damp sponge. Adhere to the front and back of each fold and trim the edges. Die Cut the corner dies from the HCD1-7202 Album Tags & Accents Die set and adhere to all the corners apart from the front.

Stamp the images from the HCPC-3853 Patchwork Daisy Border Stamp in Jet Black ink on watercolour paper. Colour with the Zig Clean Colour Brush markers and die cut with coordinating dies. Shape and add Crystal Clear glitter to the images with Dries Clear glue on a damp sponge. 

Stamp the flower images from the HCPC-3859 Buttons and Bloom Stamp set on the Super White cardstock in a variety of colours - Deep Purple, Forget-Me-Knot, and Magenta Hue. Colour the pink flowers lightly with Magenta Hue, blue flowers with French Ultramarine and the purple flowers with French Ultramarine inks and die cut with the coordinating dies. Shape with the Deluxe Flower Shaping kit and add Crystal Clear glitter to the flowers with Dries Clear glue on a damp sponge. 

Stamp the button images from the HCPC-3859 Buttons and Bloom Stamp set on white cardstock in a variety of colours - Magenta Hue and Forget-Me-Knot inks. Stamp more button images in Jet Black ink on watercolour paper. Colour the pink buttons lightly with Magenta Hue and the blue buttons with French Ultramarine inks, and colour the buttons on watercolour paper with Zig Clean Colour Brush markers. Die cut with the coordinating dies. Adhere the buttons to the centres of the flowers - the pink buttons on the light blue flowers, the blue buttons on the pink flowers and the green buttons to the purple and blue flowers as shown.

Stamp the image from the HCPC-3852 Patchwork Daisy Stamp set in Jet Black ink on watercolour paper. Colour with the Zig Clean Colour Brush Markers and die cut with the coordinating dies. Shape using the deluxe flower shaping kit.

Stamp the pocket image in Forget-Me-Knot ink on watercolour cardstock and colour in with watercolour paints before die cutting with the coordinating die.

Cut a piece of purple patterned paper 4 3/4" x 5 3/4" and using the slit die from the HCD1-7212 Petite Pocket Accents die set die cut the aperture before adhering to the back of the card by gluing around the edge only. Die cut the coordinating edge die from the HCD1-7212 Petite Pocket Accents die set from white cardstock and adhere over the pocket. Die cut the eyelet edge die from the HCD1-7202 Album Tags & Accents Die set from white cardsock. Stamp the sentiment from the JHCPC-3845 Just for You Sentiments Stamp set in Magenta Hue ink on a piece of patterned paper and die cut using the inner die from the HCD1-7202 Album Tags & Accents Die. Sponge the edge with Forget-Me-Knot ink and adhere to the base label and adhere to the top of the card back

Die cut a tag from the patterned paper and the back from white cardstock using the tag dies from the HCD1-7201 Ticket and Tags Die set. Die cut two small tag holes and adhere together and adhere to the back of the tag. Die cut another outer white tag and adhere to the back of the tag. Add a piece of white ribbon to the tag.

Adhere all of the Buttons and Blooms, Patchwork Daisy and Patchwork Daisy Border images to all of the folds as shown. 

Other Products: White Cardstock, Cantaloupe Memento Ink, Hot Glue Gun, Dimensional Tape

For more tips on creating with the Buttons and Blooms collection, watch the tutorial at https://youtu.be/WpR2XrSH0U0.

For more tips on creating with the Patchwork Daisy collection, watch the tutorial at https://youtu.be/v5BEpcSlmoI.

Instructions: My tag size is 5 1/4 x 8 3/4". Cut two pieces of cardstock 5 1/4 x 7 1/2" and glue together for added strength and stability. Cover with a piece of the paper collection and edge with Paradise Teal ink. Cut out the two decorative pieces and glue to the top and bottom corner of the tag.

Stamp the flowers using various inks and stamp the leaves with Stazon ink. Cut out using coordinating dies. Color the leaves with Bamboo Leaves Memento ink and then layer into the mold. Spritz with water and run through the Vagabond 2. Lay out to dry. Use the Deluxe flower shaping kit to shape the flower petals. I spritzed the back of the petals with a bit of water to make them easier to shape. Lay the flowers out to dry. Once dry glue two layers together

Cut out one of the tickets from the paper collection and use dimensional tape to adhere to the tag. When the flowers and leaves are dry arrange where you like and glue down using the hot glue gun.

Other Products: iCraft Vellum, Glitter Gems, Distress Oxide inks - Seedless Preserves and Shaded Lilac, Versamark ink, iCraft Super White cardstock

For more tips on creating with the pocket dies, watch the tutorial at https://youtu.be/uDhKUj9AAMo.

For more tips on creating with the tags & sentiments, watch the tutorial at https://youtu.be/eAfLuNkRda4.

Instructions: Cut a piece of white cardstock 12" x 6", score at 6" along the long side and fold to create the base card. Take the edge die of the HCD1-7213 Elegant Pocket Accents Die and die cut the front edge of the card. Die cut an outer die from white cardstock and then die cut the decorative die from the white cardstock and adhere together before adhering to the previously die cut edge. Cut a piece of purple patterned paper 5 15/16" x 5 15/16" and adhere to the inside of the card.

Stamp the images from the HCPC-3835 Leafy Accents Stamp set in Library Green ink on Super White cardstock. Colour with Leaf Green, Fern Green and Magenta Hue inks and die cut with the coordinating die. Shape using the coordinating mold, add Crystal Clear glitter using Dries Clear glue on a damp sponge. Adhere around the front decorative die as shown.

Stamp the images from the HCPC-3608 Arianna Blooms Stamp set in Versamark ink on vellum and emboss with white embossing powder. Colour on the back with the Seedless Preserves and Shaded Lilac inks and die cut with the coordinating die. Pleat the edges and add Crystal Clear glitter using Dries Clear glue on a damp sponge. Assemble the flowers as shown and adhere over the leaves as shown. Add the glitter gems to the centres of the flowers.

Die cut the eyelet tag from the HCD1-7201 Ticket and Tags Die set from white cardstock and adhere to the top of the card. Die cut the purple patterned paper using the inner plain edge die and adhere over the eyelet tag. Die cut two ornate label dies from the HCD1-7204 Ornamental Tags Die set from white cardstock and adhere together before adhering to the top of the card over the eyelet tag. Die cut the sentiment from purple cardstock and adhere to the ornate label.

Other Products: White cardstock, box, die cut machine, hot glue gun

For more tips on creating with the flower shaping molds, watch the tutorial at https://youtu.be/FSdPL7nXvQE.

Instructions: Click here to view a large photo of the box. Pre-measure your box and cut the paper from the Patchwork Daisy to match. Cover the top, sides and inside.

With white cardstock, die cut the Frame, Leafy Borders (3) and inside of the tag. Stamp the sentiment on the tag with the Manganese Blue ink and set aside. Adhere the Frame and borders on the box. Cut the outer tag out, adhere the inner part on and adhere foam dots then adhere to center of box. Stamp the leaves on white with the Library Green, color in with the Vivid Chartreuse, cut out with the coordination die, run through in the mold, ink the edges with the Emerald Green, and adhere to both the upper and lower corners on the box as shown. Stamp the flowers (8 of the medium and 4 of the larger) on white cardstock with the Plum ink, color with the Rose Madder, cut out with the coordination die, place in the mold and run through the die machine. Put 2 of the flowers together with the glue, use one of the Groove Golf tools and put a hole in the center, put the stamens in, use a hot glue gun to secure them in place, place one large and 2 small on each leaf cluster.

To complete the box, add glitter to both the leaves and flowers.

Other Products: White card stock, Seedless Preserve Distress ink, Distress applicator with foam pad, 3D foam tape, glossy accents, golden flower beads, embossing ink.

For more tips on creating with the Patchwork Daisy collection, watch the tutorial at https://youtu.be/v5BEpcSlmoI.

Instructions: Make a 6 inches by 6 inches card base from white card stock. Cut white card stock 12 inches by 6 inches and score at the 6-inch mark on the longer side. Fold to make a top folding card base. Cut a 6 by 6-inch card panel with frame from the designer paper collection and adhere to the card front.

Cut four corners from the Accents and tags die set and distress them with Seedless Preserve distress ink. Add them to the four corners of the card front with foam tape. Cut the frames from the Frame a Card die set and distress the edges with Seedless Preserve distress ink. Adhere to the four sides of the card front as shown using clear glue.

Stamp the background stamp with Embossing ink on vellum paper. Apply white embossing powder and heat set with heat tool. Add in the centre of the frame. Stamp the Daisy border image from the Patchwork daisy border stamp set using the Archival inks blue and green colors. Colour the image using the same colors. Cut with matching die and shape them a little in flower making tool kit, using a ball tool. Add a glossy button and flower pearls in the flower centres. Adhere the border images on the two sides of the card front as shown.

Cut two nesting circles from the Eyelet Circle die set to fit inside the frame. On the smaller circle, stamp the sentiment from Just For You sentiment set with black ink. Distress the edges with Distress ink. Adhere this on the bigger circle and distress the edges of this also. Apply some glitter on the border. Adhere the circle on the card front inside the frame with foam tape.

Other Products: Distress Peeled Paint Ink, White Cardstock, Diamond Stickles, Twine

For more tips on creating with the Buttons and Blooms collection, watch the tutorial at https://youtu.be/WpR2XrSH0U0.

Instructions: Card size is 4 1/4 x 6 1/4". Using your Buttons and Blooms stamp, stamp the medium and small size flower in morocco and lightly shade with the matching color and die cut with coordinating die. Shape with your deluxe flower shaping kit.

Using your leafy accents stamp, stamp your double leaves using your peeled paint ink and color with same ink. Die cut with coordinating dies and shape in the 3D shaping mold.

Using your Patchwork Pockets and Patterns stamp, stamp the zigzag with teal zeal and die cut with coordinating die.

Using your Buttons and Blooms Paper Pad cut the background mat 4" x 6". Using a craft knife cut around the edges of the hexagons to make a slit to put your sentiment mat under.

Cut a white mat 4 1/2" x 2 3/4 and stamp with "hope you get all patched up real soon" sentiment from your Hand Stitched Accents Cling set using Teal Zeal ink.

Cut your white card base 8 1/2" x 6 1/4" and using a bone folder for a cleaner line fold in half.

Assemble Card - Slide your sentiment mat under your slits in your hexagons. Slide your zig zag in and out of your sentiment mat and adhere both in place. Adhere 1 medium flower and two leaves in the bottom right corner and 1 small flower and 2 leaves in the top left corner. Tie a bow with the twine and adhere in the top center of your card. Decorate with stickles as desired.

Other Products: Mowed Lawn, Picked Raspberry and Seedless Preserve Distress inks, Crafter's Companion Zen Garden 3D Embossing folder, White Blizzard Nuvo Glitter Drops and pearls

For more tips on creating with the Patchwork Daisy collection, watch the tutorial at https://youtu.be/v5BEpcSlmoI.

Instructions: Die cut a piece of white cardstock using the decorative triangle die from Ornate Pocket Accents Die then rotate the die 90 degrees and cut the cardstock again so that the final cut resembles a bigger triangle. Trim away the extra cardstock.

Cut a piece of 4 3/4" x 6 3/4" piece of pattern paper from Patchwork Daisy Paper Collection and adhere it to a 5" x 6" white card base. Cut another piece of 4 1/4" x 6 1/4" pattern paper from the same paper collection and adhere it on a slightly bigger white cardstock. Cut the bottom left corner so that it fits the triangle die cut as shown and adhere both the pieces on the card base.

Die cut 2 pieces of white cardstocks using the Eyelet Circle and Basics Small Dies and Circle Basics Large Dies. Ink the eyelet die cut lightly using seedless preserve distress ink using Stack and Store Daubers and emboss the smaller circle die cut using Crafter's Companion Zen Garden 3D Embossing folder. Adhere them on the card front using 3D Foam Circles as shown.

Stamp the sentiment from Thank You Sentiments Cling Stamp Set on a piece of white cardstock using Jet Black Archival Ink. Trim the piece around the sentiment and adhere it on a slightly bigger piece of white cardstock inked with seedless preserve distress ink and adhere them on the top right corner of the card 3D Foam Circles.

Stamp the images from Patchwork Daisy Border Cling Stamp Set on a piece of white cardstock using Jet Black Archival Ink. Ink the images with Mowed Lawn, Picked Raspberry and Seedless Preserve Distress inks using Stack and Store Daubers. Die cut using the matching dies from Patchwork Daisy Border Die and adhere them on the card as shown using 3D Foam Circles. Add drops of White Blizzard Nuvo Glitter Drops to the flower centers and few pearls to add finishing touch.

Other Products: Hot Glue Gun, Sponge, Misti, Big Shot Plus, Scissor, Dimensional dots, VersaMark, WOW Sparkling Snow Embossing Glitter, Dimensional Tape

For more tips on creating with the Patchwork Daisy collection, watch the tutorial at https://youtu.be/v5BEpcSlmoI.

Instructions: Card size is 6 x 6". Score 6 x 12" white cardstock at 6" on the long side and fold to create the tent fold card base. Cut a 6 x 6" card front from the paper collection, ink the edges with Cactus Flower ink and die cut the circle center using the largest die from the Circle Basics Large Die. Adhere the card front to the card base using dimensional tape. Cut another 6 x 6" panel from the paper collection, ink the edges and adhere to the inside of the card.

Using the Largest die from the Circle Basics Large Die and the Eyelet die from the Eyelet Circle & Basics Small Die and white cardstock, diecut an eyelet border for the circle. Sponge with dries clear adhesive and sprinkle with Crystal Ultrafine Transparent Glitter. When dry, adhere to the card front around the diecut circle. Diecut the Elegant Pocket Accents Die from white cardstock, sponge with dries clear adhesive and sprinkle with Crystal Ultrafine Transparent Glitter. When dry, adhere to the card front as shown. Add glitter to the flowers on the circle previously cut from the card front, ink the edges with Forget-Me-Not ink and adhere to the card front using dimensional dots.

Using the Buttons and Blooms Cling Stamp set, stamp the flowers and the buttons on vellum using VersaMark, sprinkle with WOW Sparkling Snow Embossing Glitter and heat set using the Heat It tool. Color the flowers and buttons using Magenta Hue, Majestic Violet, Forget-Me-Not and Vivid Chartreuse Archival inks and Stack and Store Daubers. Diecut using the coordinating die and shape using the groove golf tool set. See Emma Lou's video here to learn how to shape them. Adhere two petals together, making sure to offset, to create the flowers. Using dimensional dots, add buttons to the flower centers.

Adhere the flowers to the card as shown.

Other Products: 3D foam tape, hot glue gun, gallery soft oil pastels

For more tips on creating with the foam paper & stamens, watch the tutorial at https://youtu.be/Oma6ctVmUD0.

For more tips on creating with the flower shaping molds, watch the tutorial at https://youtu.be/FSdPL7nXvQE.

Instructions: Create a 6 x 6" card base using white pearlised paper. Cut a piece of paper from the Merry and Bright Paper Collection 5 3/4 x 5 3/4 " and adhere to the card base using Dries Clear Adhesive.

Cut 4 pieces from white cardstock using Decorative Pocket Accents Die. Cut another piece of paper from Merry and Bright Paper Collection and cut round shape using die from Decorative Pocket Accents Die. Layer all pieces together using 3d foam tape as shown.

Cut sentiment from paper collection and attach to card using 3d foam tape.

To create flowers, stamp using Oakberry Lane Blossoms Cling Stamp Set a few times using Ranger Archival Ink Pad - Garden Patina on Art Foam and cut using the coordinating dies.

Use a heat gun to heat the petals and then shape using tool from Deluxe Flower Shaping Kit by the pressing using small ball tool in the middle. Layer the petals together using the hot glue gun making sure to offset them. Use a paper piercer to make a hole in the middle and pull through the green stamens from the assorted Bead Stamens-Medium set. Add a little hot glue to the underside of the flower to adhere. Sponge the petals with dries clear adhesive and sprinkle with Rajni Chawla's Frosting Powder.

Stamp the Large Sweet Peony Cling Stamp Set on foam paper with Ranger Archival Ink Pad - Garden Patina and cut using the coordinating dies. Colour with Gallery soft oil pastels 209. You will need 2-3 petals for each flower to create flowers.

Use an iron or heat gun to heat the petals and when start to shrink move them on the Molding Mat and press on the middle using shaping tool - using bigger one. Layer the petals together using the hot glue gun making sure to offset them or use a paper piercer to make a hole in the middle and pull through the stamens. Add a little hot glue to the underside of the flower to adhere (watch tutorial). Sponge the petals with dries clear adhesive and sprinkle with Crystal Ultrafine Transparent Glitter and Rajni Chawla's Crystal Clear glitter

Stamp the leaves using Leafy Accents Cling Stamp Set on the white paper with StazOn Ink Pad - Olive Green, cut out with the coordinating die, shade use this same ink and shape. Shape leaves using Leafy Accents Shaping Mold

Adhere the flowers and leaves attached to the card using a hot glue gun.

Other Products: White card stock

For more tips on creating with the flower shaping molds, watch the tutorial at https://youtu.be/FSdPL7nXvQE.

Instructions: Card size: 4 3/4 x 6". Start with white card stock 6 x 9 1/2" and score at 4 3/4" and 7 3/8", make 2 mountain folds and use a bone folder to get a good crease. Cut another piece of white card stock 4 3/4 x 6". On the bottom of card base (4 3/4 x 6" half) and the top of the extra piece, die cut with the plain edge of the Petite Pockets Die making sure the size is the same as the decorative Petite Pocket die you will use. Glue the bottom of the extra piece to the top 2 3/8" of the card base together (make sure you do not get glue on the other 1/2 of the card base top). Cut 4 Decorative Petite Pocket die, layer 2 together and the other 2 together separately making 1 pair of die cuts (you can do more layers if you want more of a 3D look). Cut 2 Eyelet Circles and 2 decorative paper large circles. Stamp one of the decorative paper circles with sentiment. Glue circles to Eyelet circles.

Stamp, die cut and sponge color on blossoms and leaves using Rose Madder and Deep Purple on blossom and Fern green on leaves. Stamp butterfly with Deep Purple and color with pencils. Sponge with Tea Rose and Deep Purple for Flowers and Leaf Green, Deep Purple and Rea Rose on the leaves. Form blossoms and leaves in the 3D shaping Molds, let dry (leaves and flowers are misted with water before running through die cutting machine). Cut stamen from Vellum and add yellow Nuvo to the ends. Layer blossoms together and glue. Glue stamen in the center and add Prills. Glue decorative paper to outside top (also having been cut with plain edge Petite Pocket to match card stock). And inside card. Glue circles to outside and inside then Petite Pocket die cuts. Add flowers around top (outside card) left side of circle and flowers to the circle at the bottom of inside. This will also serve as the stop for your easel so make sure 2 sides are even. Set bottom of Outside/front of card in front of the flower "stop". Card is finished. It will be a bit bulky for mailing but will fold fairly flat for an envelope.

Other Products: Purple card stock, white card stock, turquoise card stock, Embossing folder from Crafter's Companion

For more tips on creating with the flower shaping molds, watch the tutorial at https://youtu.be/FSdPL7nXvQE.

Instructions: Card size: 5 x 7". Cut 5 x 7" white card stock and run through die cutter with the embossing folder. Trim it down to 4 1/2 x 6 1/2" and glue it to a purple 4 3/4 x 6 3/4" panel. Glue this stack to a white folded card. Cut 4 corners from the Elegant Pocket Accents Die set and glue 1 to each corner at the corner where the purple panel starts. Cut the long curved decorative Elegant Pocket Accents from Turquoise and glue to bottom and left side of card. Cut the back piece of the sentiment label (Ornamental Tags Die) from purple and cut the next layer from white, cut the third layer from white and Turquoise (third layer says "A GIFT FOR YOU"). Glue then together in a stack and then glue to the vertical center and left of horizontal center a bit.

Stamp flower blossoms with Majestic Violet and Forget Me Not, sponge with the same inks. Stamp Leafy Accents with Fern Green and sponge with Forget Me Not, Majestic Violet and Leaf Green. Die cut flowers and leaves and run through die cutting machine with Shaping Molds after lightly misting with water. Let them dry then punch them in the centers with a stylist and glue together, some 4 layers, some 3 layers. Pierce the centers and add stamen, black and purple for the purple flowers, black and turquoise for the Forget Me Not flowers. Glitter all flowers.

Arrange flowers in a semi-circle on left side of card avoiding sentiment and add leaves.

Other Products: Gold Shimmer cardstock, Glitter, Flat back pearl, stone sticker, Acetate Sheet,

For more tips on creating with the tags & sentiments, watch the tutorial at https://youtu.be/eAfLuNkRda4.

For more tips on creating with the flower shaping molds, watch the tutorial at https://youtu.be/FSdPL7nXvQE.

Instructions: Ready easel card measures 5.5 x 7.5". To prepare card base take white cardstock measuring 5.5" x 15". Score on 7.5" and 11.25". To prepare mats choose pattern paper from the designer paper collection and cut a piece measuring 5.25" x 7.25", further cut 2 more pieces of same pattern paper measuring 3.5 x 5.25". Mat all 3 pattern paper on another pattern paper which is bigger by 1/16" of an inch on all four sides. Layer these mats on the card base.

To prepare frame, take a piece of white cardstock measuring 10.5 x 7.5". Score on 5"and 10" from longer side. Score on 0.5"on other side. Place a die from Eyelet Rectangle & Basics Die on one side and cut to create a frame. Stick a piece of acetate sheet on the frame. Fold it and glue from 2 sides to create a pocket. Further cut a pattern paper using same die and mat it on the pocket. Cut a frame from the white cardstock using Intricate Swrils Frames die. Glue this frame on the frame pocket. Glue this and the ready card base as shown. Keep open side up so you can change photos easily.

Stamp Blazing Poppy flowers using cactus flower on flower making paper and cut with coordinating die. Paint the flowers using same ink and shape them with small groove tool. Stamp leafy accents leaves using olive green ink and cut with coordinating die. Paint leaves using leaf green archival and shape them in shaping mold. Arrange flowers and leaves on the frame as shown.

Cut a piece of pattern paper and gold shimmer cardstock using Album Tags & Accents die. Stamp sentiment on the gold shimmer card stock using cactus flower ink. Mat the both tags on the card using dimensional tape as shown. For finished look, apply glitter on flowers using adhesive that dries clear. Glue some flat back pearls and stone stickers on the frame.

Other Products: Cardstock- White, Beads, Gems, Chameleon Pens (Olive, Green Apple), Stampin' Up Ink (Riding Hood Red, Early Espresso), Lace, Scrapbook Adhesives by 3L (Crafty Foam Tape, 3D Foam Squares Black Mix, Dual Tip Glue Pen, Adhesive Dots Micro, Adhesive Dots Medium, E-Z Runner Ultra)

For more tips on creating with the pocket dies, watch the tutorial at https://youtu.be/uDhKUj9AAMo.

Instructions: The dark green patterned paper from the Woodsy Wonderland paper collection is your background. Cut a strip of the dark red patterned paper from the same collection that is 4 x 12" and adhere lace along both long edges. Adhere this whole piece along the middle of the layout. From white cardstock, die cut 2 of each of the corner dies from the Elegant Pocket Accents. Die cut 4 of the decorative Elegant Pocket Accents. Adhere the corners to the corners of the layout. Adhere the larger pieces in a wreath shape, top, bottom and both sides. Add gold gems to the corners and around the wreath. When die cutting set aside 2 of the little 'negative' flower looking pieces that came out of the larger dies.

Mat the 4 x 6" photo twice in white cardstock and adhere to the layout using 3D foam squares. Find and cut out the "Merry and Bright" sentiment from the O Holy Night Collection. Adhere to the left of the matted photo using 3D foam squares. This is also where I added those left-over bits, flower shapes, above and below the sentiment. Add gems.

Stamp and die cut 3 sets of the small and medium poinsettias onto white cardstock using dark brown ink (Early Espresso). Add color to the flowers using ink and daubers, just to the middles of each (Riding Hood Red). Shape the flowers using the 3D Poinsettia and Holly Cluster Shaping Mold. Assemble the flowers. Add beads to the middle of each using liquid adhesive. Let dry.

Stamp and die cut 8 of the holly leaves from Merry & Bright Accents using dark brown ink. Add color to the leaves using Chameleon Pens (Olive, Green Apple). Adhere the large poinsettias around the wreath at the "joints" where the decorative dies meet. Add the small poinsettias to the middles of the decorative dies. Add the holly leaves around the large poinsettias.

Other Products: White cardstock. Big Shot Machine, creative expressions-clear glass micro beads.

For more tips on creating with the Under The Sea collection, watch the tutorial at https://youtu.be/84Re1-gaq1o.

For more tips on creating with the tags & sentiments, watch the tutorial at https://youtu.be/eAfLuNkRda4.

For more tips on creating with the pocket dies, watch the tutorial at https://youtu.be/uDhKUj9AAMo.

Instructions: Create card using Album Tags and Accents Die, as shown. Cut pattern paper from the collection using the inner die, distress the edges and adhere to card front.

Cut one Ornate Pocket Accents Die from white cardstock and adhere it on the right side edge using Designer Dries Clear Adhesive.

Cut two of the Decorative Medallion die from white cardstock and adhere them on the card on left and right edge, as shown.

Cut one eyelet edge circle from Eyelet Circle and Basics Small Die on white cardstock and on pattern paper also and adhere this pattern paper on white cardstock and adhere this circle die with foam tape to give some dimension.

Stamp decorative flora from Under the Sea Coral Cling stamp set on white cardstock with archival ink-library green and cut them with coordinating die. Color them with Zig Clean Color Real Brush Marker.

Stamp one fish and one ornate fish from Under the Sea Cling stamp Set and Under the Sea Coral Cling stamp set with archival-plum, cut it with coordinating die and color them with Zig Clean Color Real Brush Markers. Adhere them with foam tape to give some dimension.

Stamp one large seashell with archival ink-plum and cut it with coordinating die and color it with Zig Clean Color Real Brush Markers, shape and add creative expressions-clear glass micro beads and adhere all embellishments with foam tape to give some dimension, as shown.

Add sentiment from the paper collection.

Other Products: White cardstock. Big Shot Machine

For more tips on creating with the Under The Sea collection, watch the tutorial at https://youtu.be/84Re1-gaq1o.

Instructions: Card size 4 x 6" (take cardstock size 4 x 12" and fold it in half - it's a tent fold card). Cut one Intricate Swirl Frame Die on white cardstock and paste it on top of the card base, as shown. Adhere pattern paper from the collection, distress the edges of the pattern paper.

Stamp decorative flora from Under the Sea Coral Cling stamp set on white cardstock with archival ink-library green and cut them with coordinating die. Add crystal clear glitter using Designer Dries Clear Adhesive.

Cut one eyelet edge tag from Album Tags and Accents Die on white cardstock and distress the top layer with archival ink-Paradise Teal and adhere it with foam tape to give some dimension, as shown.

Cut another tag from Ornamental Tags Die, adhere it with foam tape to give some dimension and add sentiment from Cheerful Note Sentiments Cling Stamp with archival ink- jet black.

Stamp one fish and one ornate jelly fish from Under The Sea Cling stamp Set and Under the Sea Coral Cling stamp set with archival-plum and cut it with coordinating die and color them with Zig Clean Color Real Brush Markers. Adhere them with foam tape to give some dimension.

Other Products: BigShot die cutting machine, white cardstock, paper trimmer, buttons, foam tape, low tack tape

For more tips on creating with the Patchwork Daisy collection, watch the tutorial at https://youtu.be/v5BEpcSlmoI.

For more tips on creating with the Buttons and Blooms collection, watch the tutorial at https://youtu.be/WpR2XrSH0U0.

For more tips on creating with the flower shaping molds, watch the tutorial at https://youtu.be/FSdPL7nXvQE.

For more tips on creating with the pocket dies, watch the tutorial at https://youtu.be/uDhKUj9AAMo.

Instructions: Begin with a card base measuring 5 x 7", created from white card stock. Trim out a dark purple background mat from the Merry and Bright Paper Collection, just slightly smaller than the card base. Ink all edges using Ranger Archival Ink - Cactus Flower. Adhere to card base.

Locate the quilted look decorative paper within the Patchwork Daisy Paper Collection that is lighter purple in color and accented with the turquoise daisies. Trim out a section measuring 5 x 7". Next die cut the section in half on a slight diagonal using the plain die from the Fleur Border Basics Die.

Locate and trim out preprinted card panel shown in sample card. Place low tack tape along the bottom and left side of panel, stamp Snow Pine Village image onto card panel using Ranger Archival Ink Pad - Sky Blue. Remove tape.

Next, stamp the Hand-Stitched Background Cling Stamp Set onto white card stock using Ranger Archival Ink Pad - Sky Blue. Trim out stamped background to be just slightly larger than preprinted card panel. Adhere card panel and stamped background together. Adhere to card base using dimensional foam tape.

Adhere decorative daisy patterned die cut paper created with the Fleur Border Basics Die to card base as shown using dimensional foam tape along sides and bottom, and clear adhesive to top portion which overlaps illustration.

Die cut small corner lace like accent from within the Ornate Pocket Accents Die. Adhere to bottom of card base as shown.

Stamp one inking of the Patchwork Daisy Border and one inking of the smallest daisy flowers found in the Buttons and Blooms Cling Stamp Set onto white card stock using Ranger Archival Ink - Jet Black. Stamp smallest poinsettias onto pink patterned paper from the Patchwork Daisy Paper Collection and the holly clusters from green patterned paper within the Merry and Bright Collection. Color poinsettia petal tips slightly using Ranger Archival Ink - Cactus Flower, holly clusters and leaves on border using Ranger Archival - Leaf Green, and all daisy images using Ranger Archival Ink - Sky Blue. Die cut all elements using coordinating dies. Hand shape daisies slightly using Deluxe Flower Shaping Kit, and shape poinsettias and holly clusters using coordinating shaping mold. Create four poinsettia clusters using poinsettia flower and holly leaves. Leave the rest of the poinsettias as single blooms with no greenery.

Stamp one inking of the patches from the Pocket and Patterns Cling Stamp Set onto a light decorative paper from the Buttons and Blooms Paper Collection using Ranger Archival Ink - Sky Blue. Die cut using coordinating dies. Ink all edges with Ranger Archival Ink - Sky Blue. Adhere to card base as shown.

Trim out preprinted sentiment from the Merry and Bright Paper Collection. Snip banner end into sentiment and ink all edges using Ranger Archival Ink - Cactus Flower. Adhere to card as shown. Using scissors, snip apart daisy border die cut to create a free standing embellishment. Adhere Patchwork Daisy Border to card as shown. Adhere single poinsettias and holly clusters to floral cluster as shown.

Using a dries clear adhesive, apply Heart of Gold Prills to all poinsettia centers and buttons to patchwork daisies. Apply dries clear glue to all florals and foliage and sprinkle with Rajni Chawla's Crystal Clear. Add Crystal Ultrafine Transparent Glitter to preprinted card panel in background using a dries clear adhesive.

Other Products: Water color paper, kraft card stock, black embossing powder

For more tips on creating with the Merry and Bright collection, watch the tutorial at https://youtu.be/6bgO6epBuBI.

Instructions: Cut a 5 x 7" card base in white card stock. Cut a piece of kraft cardstock slightly smaller than the card base and adhere to card base. Cut the Intricate Swirl Frame Die in white card stock and adhere to the craft piece. Cut blue designer paper from the Merry and Bright Paper Collection to fit inside Intricate Swirl Die. Create the oval frame with by cutting out the large Eyelet Oval in kraft and cut out the center with the next smaller oval die. Cut out an oval in the center of the blue designer paper with the same oval die and adhere the kraft frame over the cut out.

Heat emboss the snowman from the Frolicking Frosty set in black on water color paper, color with Zig markers. Adhere to the center of the Intricate Swirl Die, adhere the blue panel with foam tape for dimension on top with the snowman centered.

Heat emboss snowflakes from the Snow Kissed set in white embossing powder on kraft card stock and fussy cut, adhere as shown. Stamp the sentiment from the Merry Little Christmas Cling Stamp Set, cut out with circle die, cut out the scallop die from the Furry-tailed Frolic Die in kraft card stock, adhere the sentiment circle with foam tape to the scallop circle and adhere to card, as shown.

Other Products: Silver mirri card, blue twine or yarn, gems, Granny Apple Green and Highland Heather ink pads (Stampin Up!), double sided glue, hot glue, a Bar of chocolate!

For more tips on creating with the O Holy Night collection, watch the tutorial at https://youtu.be/UWDeK6soJ0E.

For more tips on creating with the Merry and Bright collection, watch the tutorial at https://youtu.be/6bgO6epBuBI.

Instructions: Click here to view a larger photo of this project. Measure the bar of chocolate across the front and cut a strip of paper the width of the chocolate.

Measure the strip of paper around the chocolate bar and overlap it by approx. 1", ink around the edges of the paper and glue the band in place (only put glue on the overlap so that the band slides off).

Cut a decorative strip from the paper pad and stick in place along the bottom edge using double sided tape

Die cut a solid ornament shape using a blue paper from the paper pad. Diecut a second ornament in silver mirri card and die cut the centre using the decorative die. Glue the 2 pieces together to create the bauble. Lightly shape and add to the belly band using hot glue (take the chocolate out the band so you don't melt the chocolate!). Add gems to the centre of each snowflake and the top of the ornament.

Stamp the trees onto blue paper using Granny apple green ink, die cut and shape using the flower shaping kit. Add to the belly band using hot glue and tuck the trunks of the trees under the decorative edge.

Create the Best wishes tag in the same way as the bauble. Thread the twine or yarn through this and position to the belly band using hot glue.

Tie the smaller tag to the larger ornament bauble and tie in a bow.

Other Products: Two shades of purple cardstock, silver cardstock, lavender seam binding ribbon, twine, light weight cardboard, small hole punch.

For more tips on creating with the flower shaping molds, watch the tutorial at https://youtu.be/FSdPL7nXvQE.

For more tips on creating with the Merry and Bright collection, watch the tutorial at https://youtu.be/6bgO6epBuBI.

Instructions: Click here to view a larger photo of this project. Cut out two of the solid ornaments from the Noel Ornament Die in the darker purple cardstock and one in the light weight cardboard, punch small hole in the top of the ornaments so a twine loop can be attached, adhere them together with the light weight cardboard in the center to give the ornament thickness. Cut out two of the detailed ornaments in the lighter purple, punch small holes in the top of each and adhere one to each side.

Stamp and sponge the poinsettias in Lilac Posies, cut out with corresponding dies and use the tutorial for Shaping molds to sculpt flowers, add prills and Frosting Powder. Stamp pinecones from Silent Night Scroll set and the branched from the Snowy Pine Village set in Rich Chocolate, cut out with corresponding dies, and sponge with Rich Cocoa and Bamboo Leaves. Cut out Silent Night die from the Silent Night Scroll Die and the holly leaves from the Merry and Bright Accents Die in silver cardstock.

Adhere the bows, holly leaves, poinsettias, pinecones, pinecones, Silent Night and seam binding bow as shown. Tie twine loop for hanging.

Other Products: 2 small envelopes, Brown cardstock, Creme cardstock, very small magnets, 3d foam pads

For more tips on creating with the Oakberry Lane collection, watch the tutorial at https://youtu.be/HirfUN8NEYY.

For more tips on creating with the Patchwork Daisy collection, watch the tutorial at https://youtu.be/v5BEpcSlmoI.

Instructions: Take the 2 envelopes and glue the flap of one envelope in the other envelope, now fold it double and you have the map, place the magnets on the inside on each side. Cover the whole map with paper from the collection.

Cut a piece of Brown Cardstock at 3 5/8 x 5 1/8" and glue this on the cover, cut a piece of Creme Cardstock at 5 x 3 1/2". Take your Hand stitched background stamp and Morocco Ink and stamp it on the creme cardstock, then take the big flower of the patchwork Daisy set and stamp it with the Rich Cocoa on top of the Creme cardstock, now glue this one down on the cover too.

Stamp with the Oak berry lane Blossom set and Rich Cocoa 2x the Big flower and 3x the leaves, now cut them out with the coordinating dies. Color the center of the flowers with Buttercup and the outsides with the Morocco, color the leaves with Leaf Green and some spots with the morocco, Place the flowers and leaves in the mold, spray them light with water put the lid on it and run it through the machine. Now glue 2 flowers on top of each other, make a hole in the center and pull the stamens through, stamp 2 acorns with Rich cocoa and color them very light with that too then on top some Morocco, cut them out with the coordinating die, Stamp with Rich Cocoa 2 sets of the pine tree leaves and color them with leaf green, cut them out with the coordinating die, now glue everything on the cover of your card in a nice composition.

Take a filmstrip from the big album and cut out 2 pieces and glue them on 3 sides on the inside, then you have 2 pockets to put a photo in.

Now cut 2 pieces of brown cardstock 3 1/2 x 5 1/2 for the inside of the envelopes.

Other Products: Stickles:Yellow, Zig Clean Color Pens

For more tips on creating with the flower shaping molds, watch the tutorial at https://youtu.be/FSdPL7nXvQE.

Instructions: Score your white cardstock to 5 x 7" then cut a piece of paper from the Patchwork Daisy collection to 4.75 x 6.75" which will be your card front. 

Next diecut the frame from the accents die set using the eyelet with white cardstock. Next mat it with paper from the Tropical Paradise set. Stamp the sentiment from the Heartfelt Love collection with your black memento ink.

Stamp and diecut your coneflower onto watercolor paper with Stazon black ink. Next color in your image using the zig clean color pens and add some yellow stickles to your coneflowers to add some extra flair.

Finally, fussy cut the parrot from the Tropical Paradise set and adhere to your framed sentiment.

Other Products: White cardstock, Clear dry glue, Pencil Colors, 3D foam tape

For more tips on creating with the Patchwork Daisy collection, watch the tutorial at https://youtu.be/v5BEpcSlmoI.

Instructions: The finished card measures 6 x 6". Cut white cardstock 12 x 6", score at 6" from the longest side and fold. Choose pattern paper from the paper collection, cut it to size 5-3/4 x 5-3/4. Adhere on top of white cardstock with clear dry glue.

Cut white cardstock 2 x 6", stamp on one side using Patchwork Daisy Border Cling Stamp Set and die cut using the coordinating die. Color the image with pencil colors and score the left-over cardstock at every 1/4 inch. Arrange it in the center of card with 3D foam tape.

Stamp white cardstock with Patchwork Daisy Cling Stamp Set and die cut using the coordinating die. Color the image with pencil colors.

Die cut banner out of pattern paper using Ornamental Tags Die and mat with white cardstock. Stamp with sentiment from Thank You Sentiments Cling Stamp Set using Archival Ink Jet Black.

Once all the elements are ready arrange them as shown. Apply Rajni Chawla's Crystal Clear with clear drying glue on flowers.

Other Products: White cardstock, clear dry glue, Buttons, Twine, acetate sheet, Double sided tape, Archival ink Cobalt For more tips on creating with the Buttons and Blooms collection, watch the tutorial at https://youtu.be/WpR2XrSH0U0.

For more tips on creating with the Patchwork Daisy collection, watch the tutorial at https://youtu.be/v5BEpcSlmoI.

Instructions: Click on my name below and it will take you to my blog where you'll see lots more photos. Cut white cardstock 9-1/4 x 14-1/2". From the longest side score at 2, 7, 9, 14 and 1/2 inch, fold on all score lines and apply double sided tape on 1/2 inch space. Die cut the back side of the bag using the largest oval die from the Eyelet Oval Die set. Attach clear acetate sheet from inside for see through window. Attach 1/2 inch space to another side for creating bag.

Score another side (9-1/4 inch) at 2 inch from one side and 1-1/4 inch for the upper closer. Cut along all the 2 inch score line till it meets the horizontal score lines. Apply double sided tape on 2 inch space. Overlap the side flaps first and then center flaps for bottom closer.

Mat all the sides of bag with pattern paper. For the upper closer, cut white cardstock 5 x 4". Die cut one side using the corner die from the Ornate Pocket Accents Die set, mat with pattern paper and attach it to the upper part with double sided tape. Optional - adhere buttons in the center as shown. Stamp pattern paper using the Patchwork Pocket & Patterns Cling Stamp Set and die cut using the coordinating die. Die cut tags and tickets out of pattern paper using the Ticket and Tags Die

For flowers stamp white cardstock with Buttons and Blooms Cling Stamp Set using Archival ink Cobalt. Die cut the images using the coordinating die. Color the flower petals using Archival ink -Cobalt. Shape the flowers using Groove Golf Tool. Apply Crystal Clear Glitter on the flowers with clear dry glue.

Stamp white cardstock with Leafy Accents Cling Stamp Set using Archival ink - Library Green, die cut using coordinating die. Color the leaves using Archival ink - Olive and colorbox ink Olive Pastel. Shape the leaves using Leafy Accents Shaping Mold

Arrange die cut pocket to the front side of the bag and arrange the flowers and leaves around as shown. Tie die cut tags to a twine and wrap around the closer part. Finish off with a die cut ticket from the pattern paper.